Home » Forums » Community Edition » Help

fresh install of trixbox, zaptel voice missing

skywise
Posts: 5
 Member Since:
2007-11-14
Submitted by skywise on Thu, 01/17/2008 - 3:28pm.

I was running an old version of trixbox with a 4 channel zaptel PCI card (wctdm driver) perfectly fine, no issues.
I tried a package update a few days ago and it looks like too much got updated and it ate my phone system, no calls in or out, voicemail messages lost, very nasty.
So, I wrote down my entire configuration, DLed the latest CD for trixbox (V2.4.2)
and blew away the entire box and installed from scratch.
The config went back in clean and most of the system worked fine.
The one thing messed up is my zaptel.
If I pick up a POTS internal phone and call a SIP ext, it works fine.
If I pick up a SIP ext and call the POTS ext, neither side can hear the other.
If a call comes in from the outside into the zaptel, the caller can't hear anything and I can't hear them on any of my SIP exts.
caller ID, dialing and all that seems to work fine.

Anyone encounter anything like this? Any suggestions?

Sky

‹ Problems with line hangup detection (Sangoma card) Call Recording ›

&nbsp

markwho
Posts: 675
 Member Since:
2006-09-24
In zapata.conf make sure
Thu, 01/17/2008 - 3:40pm

In zapata.conf make sure echotraining is commented out.
;echotraining=800


&nbsp

skywise
Posts: 5
 Member Since:
2007-11-14
That's got 1/2 the problem
Thu, 01/17/2008 - 5:48pm

That's got 1/2 the problem licked, I can now call into the house using the zaptel trunk and answer with a sip ext.
The zaptel ext still can't answer a call though. But it can originate one still.
(it answers but no voice either way)


&nbsp

phk
Posts: 47
 Member Since:
2007-08-20
do the same with your zaptel ext
Thu, 01/17/2008 - 8:55pm

check that your zaptel extension has also no value to echotraining


&nbsp

skywise
Posts: 5
 Member Since:
2007-11-14
Thanks for the hint, I found
Fri, 01/18/2008 - 2:41am

Thanks for the hint, I found it!
My extension in the gui had a spot for echotraining and it was 800, setting it to blank fixed it.

Thanks again!


&nbsp

Thirdnet
Posts: 7
 Member Since:
2007-05-15
Nothing seems to be helping
Fri, 01/25/2008 - 10:18am

Well, I have read about every post I can find on this subject and followed all the suggestions. I still have no voice for incoming calls on a Zaptel extension, but I can make outgoing calls with voice.

As I stated, I have tried commenting out the echotraining, I have tried reducing it to 128.

Any other suggestions?


&nbsp

zforum69
Posts: 81
 Member Since:
2007-04-18
post your CLI output and
Fri, 01/25/2008 - 12:01pm

post your CLI output and lets us all have a look at what is happening.

Z


&nbsp

Thirdnet
Posts: 7
 Member Since:
2007-05-15
CLI from call
Sun, 01/27/2008 - 5:42pm

Below is the output. If there is some other command that will provide more detail, please let me know.

[pbx.thirdnet.local ~]# asterisk -r -vvv
Asterisk 1.4.17-1 RPM by vc-rpms@voipconsulting.nl, Copyright (C) 1999 - 2007 Digium, Inc. and others.
Created by Mark Spencer
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details.
This is free software, with components licensed under the GNU General Public
License version 2 and other licenses; you are welcome to redistribute it under
certain conditions. Type 'core show license' for details.
=========================================================================
== Parsing '/etc/asterisk/asterisk.conf': Found
== Parsing '/etc/asterisk/extconfig.conf': Found
Connected to Asterisk 1.4.17-1 RPM by vc-rpms@voipconsulting.nl currently running on pbx (pid = 2397)
Verbosity is at least 3
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
-- Starting simple switch on 'Zap/1-1'
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
-- Executing [s@from-pstn:1] Set("Zap/1-1", "__FROM_DID=s") in new stack
-- Executing [s@from-pstn:2] Gosub("Zap/1-1", "app-blacklist-check|s|1") in new stack
-- Executing [s@app-blacklist-check:1] LookupBlacklist("Zap/1-1", "") in new stack
-- Executing [s@app-blacklist-check:2] GotoIf("Zap/1-1", "0?blacklisted") in new stack
-- Executing [s@app-blacklist-check:3] Return("Zap/1-1", "") in new stack
-- Executing [s@from-pstn:3] GotoIf("Zap/1-1", "1 ?cidok") in new stack
-- Goto (from-pstn,s,5)
-- Executing [s@from-pstn:5] NoOp("Zap/1-1", "CallerID is "Thirdnet Work Cell " ") in new stack
-- Executing [s@from-pstn:6] Goto("Zap/1-1", "from-did-direct|210|1") in new stack
-- Goto (from-did-direct,210,1)
-- Executing [210@from-did-direct:1] Macro("Zap/1-1", "exten-vm|210|210") in new stack
-- Executing [s@macro-exten-vm:1] Macro("Zap/1-1", "user-callerid") in new stack
-- Executing [s@macro-user-callerid:1] NoOp("Zap/1-1", "user-callerid: Thirdnet Work Cell 4154154155") in new stack
-- Executing [s@macro-user-callerid:2] Set("Zap/1-1", "AMPUSER=4154154155") in new stack
-- Executing [s@macro-user-callerid:3] GotoIf("Zap/1-1", "0?report") in new stack
-- Executing [s@macro-user-callerid:4] GotoIf("Zap/1-1", "0?start") in new stack
-- Executing [s@macro-user-callerid:5] Set("Zap/1-1", "REALCALLERIDNUM=4154154155") in new stack
-- Executing [s@macro-user-callerid:6] NoOp("Zap/1-1", "REALCALLERIDNUM is 4154154155") in new stack
-- Executing [s@macro-user-callerid:7] Set("Zap/1-1", "AMPUSER=") in new stack
-- Executing [s@macro-user-callerid:8] Set("Zap/1-1", "AMPUSERCIDNAME=") in new stack
-- Executing [s@macro-user-callerid:9] GotoIf("Zap/1-1", "1?report") in new stack
-- Goto (macro-user-callerid,s,13)
-- Executing [s@macro-user-callerid:13] NoOp("Zap/1-1", "TTL: ARG1: 210") in new stack
-- Executing [s@macro-user-callerid:14] GotoIf("Zap/1-1", "0?continue") in new stack
-- Executing [s@macro-user-callerid:15] Set("Zap/1-1", "__TTL=64") in new stack
-- Executing [s@macro-user-callerid:16] GotoIf("Zap/1-1", "1?continue") in new stack
-- Goto (macro-user-callerid,s,23)
-- Executing [s@macro-user-callerid:23] NoOp("Zap/1-1", "Using CallerID "Thirdnet Work Cell " ") in new stack
-- Executing [s@macro-exten-vm:2] Set("Zap/1-1", "FROMCONTEXT=exten-vm") in new stack
-- Executing [s@macro-exten-vm:3] Set("Zap/1-1", "VMBOX=210") in new stack
-- Executing [s@macro-exten-vm:4] Set("Zap/1-1", "EXTTOCALL=210") in new stack
-- Executing [s@macro-exten-vm:5] Set("Zap/1-1", "CFUEXT=") in new stack
-- Executing [s@macro-exten-vm:6] Set("Zap/1-1", "CFBEXT=") in new stack
-- Executing [s@macro-exten-vm:7] Set("Zap/1-1", "RT=15") in new stack
-- Executing [s@macro-exten-vm:8] Macro("Zap/1-1", "record-enable|210|IN") in new stack
-- Executing [s@macro-record-enable:1] GotoIf("Zap/1-1", "0?2:4") in new stack
-- Goto (macro-record-enable,s,4)
-- Executing [s@macro-record-enable:4] AGI("Zap/1-1", "recordingcheck|20080127-162746|1201480065.31") in new stack
-- Launched AGI Script /var/lib/asterisk/agi-bin/recordingcheck
recordingcheck|20080127-162746|1201480065.31: Inbound recording not enabled
-- AGI Script recordingcheck completed, returning 0
-- Executing [s@macro-record-enable:5] NoOp("Zap/1-1", "No recording needed") in new stack
-- Executing [s@macro-exten-vm:9] Macro("Zap/1-1", "dial|15|tr|210") in new stack
-- Executing [s@macro-dial:1] GotoIf("Zap/1-1", "1?dial") in new stack
-- Goto (macro-dial,s,3)
-- Executing [s@macro-dial:3] AGI("Zap/1-1", "dialparties.agi") in new stack
-- Launched AGI Script /var/lib/asterisk/agi-bin/dialparties.agi
dialparties.agi: Starting New Dialparties.agi
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
dialparties.agi: Caller ID name is 'Thirdnet Work Cell' number is '4154154155'
dialparties.agi: Methodology of ring is 'none'
-- dialparties.agi: Added extension 210 to extension map
-- dialparties.agi: Extension 210 cf is disabled
-- dialparties.agi: Extension 210 do not disturb is disabled
-- dialparties.agi: dbset CALLTRACE/210 to 4154154155
== Manager 'admin' logged off from 127.0.0.1
-- AGI Script dialparties.agi completed, returning 0
-- Executing [s@macro-dial:10] Dial("Zap/1-1", "ZAP/3|15|tr") in new stack
-- Called 3
-- Zap/3-1 is ringing
== Manager 'admin' logged off from 127.0.0.1
-- Zap/3-1 is ringing
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
-- Zap/3-1 is ringing
== Manager 'admin' logged off from 127.0.0.1
-- Zap/3-1 answered Zap/1-1
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
-- Hungup 'Zap/3-1'
== Spawn extension (macro-dial, s, 10) exited non-zero on 'Zap/1-1' in macro 'dial'
== Spawn extension (macro-dial, s, 10) exited non-zero on 'Zap/1-1' in macro 'exten-vm'
== Spawn extension (macro-dial, s, 10) exited non-zero on 'Zap/1-1'
-- Executing [h@macro-dial:1] Macro("Zap/1-1", "hangupcall") in new stack
-- Executing [s@macro-hangupcall:1] ResetCDR("Zap/1-1", "w") in new stack
-- Executing [s@macro-hangupcall:2] NoCDR("Zap/1-1", "") in new stack
-- Executing [s@macro-hangupcall:3] GotoIf("Zap/1-1", "1?skiprg") in new stack
-- Goto (macro-hangupcall,s,6)
-- Executing [s@macro-hangupcall:6] GotoIf("Zap/1-1", "1?skipblkvm") in new stack
-- Goto (macro-hangupcall,s,9)
-- Executing [s@macro-hangupcall:9] GotoIf("Zap/1-1", "1?theend") in new stack
-- Goto (macro-hangupcall,s,11)
-- Executing [s@macro-hangupcall:11] Hangup("Zap/1-1", "") in new stack
== Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'Zap/1-1' in macro 'hangupcall'
== Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'Zap/1-1'
-- Hungup 'Zap/1-1'
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
== Manager 'admin' logged off from 127.0.0.1
== Parsing '/etc/asterisk/manager.conf': Found
== Parsing '/etc/asterisk/manager_additional.conf': Found
== Parsing '/etc/asterisk/manager_custom.conf': Found
== Manager 'admin' logged on from 127.0.0.1
pbx*CLI>


&nbsp

Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.