I have this problem with sangoma A102DE, instaled on IBM System X3200 M2
ALARM RED=ON, LOF=ON
can Anybody help me?
wanpipemon -i w1g1 -c Ta
***** w1g1: T1 Rx Alarms (Framer) *****
ALOS: OFF | LOS: OFF
RED: ON | AIS: OFF
LOF: ON | RAI: OFF
***** w1g1: T1 Rx Alarms (LIU) *****
Short Circuit: OFF
Open Circuit: OFF
Loss of Signal: OFF
***** w1g1: T1 Tx Alarms *****
AIS: OFF | YEL: ON
***** w1g1: T1 Performance Monitoring Counters *****
Line Code Violation : 1899
Bit Errors (CRC6/Ft/Fs) :0
Out of Frame Errors : 0
Rx Level : > -2.5db
----------------
wanpipemon -i w2g1 -c Ta
***** w2g1: T1 Rx Alarms (Framer) *****
ALOS: OFF | LOS: OFF
RED: ON | AIS: OFF
LOF: ON | RAI: OFF
***** w2g1: T1 Rx Alarms (LIU) *****
Short Circuit: OFF
Open Circuit: OFF
Loss of Signal: OFF
***** w2g1: T1 Tx Alarms *****
AIS: OFF | YEL: ON
***** w2g1: T1 Performance Monitoring Counters *****
Line Code Violation : 0
Bit Errors (CRC6/Ft/Fs) :0
Out of Frame Errors : 0
Rx Level : -2.5db to -5db
#================================================
# WANPIPE1 Configuration File
#================================================
#
# Date: Wed Dec 6 20:29:03 UTC 2006
#
# Note: This file was generated automatically
# by /usr/local/sbin/setup-sangoma program.
#
# If you want to edit this file, it is
# recommended that you use wancfg program
# to do so.
#================================================
# Sangoma Technologies Inc.
#================================================
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 4
PCIBUS = 10
FE_MEDIA = T1
FE_LCODE = B8ZS
FE_FRAME = ESF
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
TE_HIGHIMPEDANCE = NO
TE_RX_SLEVEL = 360
LBO = 0DB
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 24
TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS Blue Alarm and keep line down
#wanpipemon -i w1g1 -c Ttx_ais_off to disable AIS maintenance mode
#wanpipemon -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
TDMV_HW_DTMF = YES # YES: receive dtmf events from hardware
TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz events from hardware
HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation enabled with nlp (default)
# OCT_SPEECH: improves software tone detection by disabling NLP (echo possible)
# OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions.
HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of incoming media (must have hwdtmf enabled)
HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the line - could break fax
HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo cancelation
HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software tone detection (possible echo)
HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level to be maintained (-20 default)
HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level to be maintained (-20 default)
HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to be applied to tx signal
HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to be applied to tx signal
[w1g1]
ACTIVE_CH = ALL
TDMV_HWEC = YES
MTU = 8
#================================================
# WANPIPE2 Configuration File
#================================================
#
# Date: Wed Dec 6 20:29:03 UTC 2006
#
# Note: This file was generated automatically
# by /usr/local/sbin/setup-sangoma program.
#
# If you want to edit this file, it is
# recommended that you use wancfg program
# to do so.
#================================================
# Sangoma Technologies Inc.
#================================================
[devices]
wanpipe2 = WAN_AFT_TE1, Comment
[interfaces]
w2g1 = wanpipe2, , TDM_VOICE, Comment
[wanpipe2]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 4
PCIBUS = 10
FE_MEDIA = T1
FE_LCODE = B8ZS
FE_FRAME = ESF
FE_LINE = 2
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
TE_HIGHIMPEDANCE = NO
TE_RX_SLEVEL = 360
LBO = 0DB
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 2
TDMV_DCHAN = 24
TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS Blue Alarm and keep line down
#wanpipemon -i w1g1 -c Ttx_ais_off to disable AIS maintenance mode
#wanpipemon -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
TDMV_HW_DTMF = YES # YES: receive dtmf events from hardware
TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz events from hardware
HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation enabled with nlp (default)
# OCT_SPEECH: improves software tone detection by disabling NLP (echo possible)
# OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions.
HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of incoming media (must have hwdtmf enabled)
HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the line - could break fax
HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo cancelation
HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software tone detection (possible echo)
HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level to be maintained (-20 default)
HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level to be maintained (-20 default)
HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to be applied to tx signal
HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to be applied to tx signal
[w2g1]
ACTIVE_CH = ALL
TDMV_HWEC = YES
MTU = 8
Member Since:
2011-09-28